For non-professional painters, buying the paint, then mixing it with water is all we have to do. However, experts pay a lot of attention to the thickness of the paint. It affects everything, from how simple it can be sprayed to how much it jams the sprayer.
If you would like a successful and long-lasting paint layer, you are at the right place. This article will give you comprehensive guidance on thinning the pain for a Wagner sprayer. Please scroll to discover!
Best Wagner Paint Sprayer – The Ultimate Buying Guide For 2021
Wagner Flexio 590 Vs 3000: The Ultimate Comparison
Is it really necessary to thin paint for a Wagner sprayer?
Yes. Most beginning or hobby sprayers need to dilute the paint since they lack the strength to push out anything harder than the dirty spots. Yet, thinning the paint with a high-quality sprayer can provide a nicer finish.
Latex and alkyd are the two kinds of paint available. Thicker than the other one. A Wagner sprayer can work with both of them.
That thickness is also known as stickiness, which essentially refers to how smoothly latex and oil paints flow.
If the paint is excessively thick, it will block the nozzle of your spray gun several times. Everything gets words when you’re in a rush to avoid having drying spots where you previously painted.
Cleaning the Wagner sprayer will take you about 10-15 minutes each time it jams. Thinning the paint before using allows you to get the job done earlier.
On the other hand, avoid over-thinning your latex paint. You may wind up with a messy overspray disaster on your hands if you do.
How To Thin Paint For A Wagner Sprayer?
Thinning is the very first preparation for your paint job. You can thin the paint yourself with these steps:
Step 1: Test the thickness of the paint
Give your paint a thorough stir for 30-60 seconds. You may perform this by shaking the can.
With leftover paint that has been sitting for a long period, this step is even more critical. With new paint, you can usually skip that step.
Then, open the container and apply the paint with your wooden paint stick. Mix the paint in a rotational movement. Mix it up and down to blend any paint that has collected at the bottom of the bucket.
Take the stick out of the paint after spinning and observe how the paint drops off the stick. It will most likely leak in one constant flow for a few seconds before draining on and off. This observation step lets us know if the paint is too thick to spray and needs thinning.
Use the stick to check the paint’s thickness
You can use the funnel instead to test the paint’s thickness. If the paint runs out of the funnel in a single, steady stream, it is thin enough.
Step 2: Add water into the paint
Mix the water and the paint. If required, you may add a bit of extra water afterward. Also, don’t worry if you apply too much water; you can always add additional paint.
We have found that higher-quality paints are a touch thicker and may require a little more water.
Rather than water, some experts prefer to utilize a paint conditioner. It can make your paint job look smoother, but it isn’t necessary.
Step 3: Stir the mixture
Gently stir in a tiny amount of water while stirring the paint. As previously said, continue to use your stir stick in an up-down spiral motion.
Take your paint stick out while stirring the liquid to see how nicely the mixture comes off the stick. Add a bit of extra water if your paint is too thick.
Stir the mixture of paint and water
Step 4: Pour the paint into the Wagner sprayer
Pour a little paint mixture into the sprayer. After that, test the spray vertically to ensure that the spray pattern and viscosity are satisfactory.
Pour the paint into the Wagner sprayer
If the paint is still thick, a slight peel texture may appear. If the paint mixture is too thin, it will leak and take a long time to dry.
When the liquid doesn’t leak and dries rapidly, it’s a perfect consistency.
How To Use A Wagner Sprayer Effectively?
You have thinned the paint. Your workpiece will be perfect if you know how to use the Wagner sprayer properly. Don’t worry! We will help by sharing some tips as following:
- Some light will help you discover spots that require additional paint. Put the light at an angle and you will see how it works. Of course, you do not need it when you are painting outside.
- Begin spraying in a corner and move back and forth. You can extend each stroke by roughly half the flow path on the following stroke.
- To prevent dripping, keep the gun going at a constant pace.
- Wipeout droplets as soon as you notice them, and then softly spray over the brushwork to hide them.
- Keep a damp towel or cloth on hand. If you drop paint on something, you shouldn’t even be painting.
- We recommend spraying a layer of primer first. It helps you assure the tone you paint will be your expectation. This method is important, especially if you apply the light hue over the darker one.
- It may be simpler to edge off the doors, frames, windows, fixtures, and other areas using a brush or Wagner edge roller. These areas require you to work carefully.
Use rollers for the edges
You may know the importance of thinning the paint for a Wagner sprayer. We also include the steps for doing it properly. We hope that this article can assist you in your paint jobs.
If you have any questions, please feel free to ask. We are always willing to support you!
Thank you for reading!